Bend Tool selection names is confusing

1 Vote(s) - 5 Average

Bend Tool selection names is confusing

puzzledpaul
Offline

low down bum

Posts: 125
Threads: 3
Joined: May 2012

#16

12-19-2012, 10:42 PM

Peter - try your object as in post 26, with bend centre being an edge,as shown - but rod top a vert.

Then compare putting rod top one(blue) section away from centre and 5 (blue)sections from centre.

pp

« Next Oldest | Next Newest »

Users browsing this thread: 1 Guest(s)

Messages In This Thread

Bend Tool selection names is confusing - by oort - 12-18-2012, 10:27 PM

RE: Bend Tool selection names is confusing - by PeterC (PC) - 12-19-2012, 01:47 AM

RE: Bend Tool selection names is confusing - by Fonte Boa - 12-19-2012, 01:59 AM

RE: Bend Tool selection names is confusing - by oort - 12-19-2012, 02:25 AM

RE: Bend Tool selection names is confusing - by PeterC (PC) - 12-19-2012, 03:33 AM

RE: Bend Tool selection names is confusing - by oort - 12-19-2012, 04:16 AM

RE: Bend Tool selection names is confusing - by PeterC (PC) - 12-19-2012, 04:17 AM

RE: Bend Tool selection names is confusing - by Fonte Boa - 12-19-2012, 11:50 AM

RE: Bend Tool selection names is confusing - by oort - 12-19-2012, 03:15 PM

RE: Bend Tool selection names is confusing - by PeterC (PC) - 12-19-2012, 08:46 PM

RE: Bend Tool selection names is confusing - by Fonte Boa - 12-19-2012, 09:43 PM

RE: Bend Tool selection names is confusing - by puzzledpaul - 12-19-2012, 10:30 PM

RE: Bend Tool selection names is confusing - by puzzledpaul - 12-19-2012, 10:06 PM

RE: Bend Tool selection names is confusing - by puzzledpaul - 12-19-2012, 10:16 PM

RE: Bend Tool selection names is confusing - by PeterC (PC) - 12-19-2012, 10:29 PM

RE: Bend Tool selection names is confusing - by puzzledpaul - 12-19-2012, 10:42 PM

RE: Bend Tool selection names is confusing - by PeterC (PC) - 12-19-2012, 10:55 PM

RE: Bend Tool selection names is confusing - by puzzledpaul - 12-19-2012, 11:19 PM

RE: Bend Tool selection names is confusing - by PeterC (PC) - 12-19-2012, 11:48 PM

RE: Bend Tool selection names is confusing - by oort - 12-20-2012, 01:05 AM

RE: Bend Tool selection names is confusing - by Fonte Boa - 12-20-2012, 03:09 AM

RE: Bend Tool selection names is confusing - by puzzledpaul - 12-20-2012, 04:14 PM

RE: Bend Tool selection names is confusing - by oort - 12-20-2012, 11:12 PM

RE: Bend Tool selection names is confusing - by puzzledpaul - 12-20-2012, 11:39 PM

RE: Bend Tool selection names is confusing - by oort - 12-20-2012, 11:58 PM

RE: Bend Tool selection names is confusing - by puzzledpaul - 12-21-2012, 08:45 AM

RE: Bend Tool selection names is confusing - by oort - 12-21-2012, 05:41 PM

RE: Bend Tool selection names is confusing - by puzzledpaul - 12-21-2012, 06:57 PM

RE: Bend Tool selection names is confusing - by oort - 12-21-2012, 09:23 PM

RE: Bend Tool selection names is confusing - by puzzledpaul - 12-21-2012, 09:38 PM