+- Wings 3D Development Forum (https://www.wings3d.com/forum)
+-- Forum: Wings 3D (https://www.wings3d.com/forum/forumdisplay.php?fid=1)
+--- Forum: Bug Reports (https://www.wings3d.com/forum/forumdisplay.php?fid=12)
+--- Thread: [Fixed] Tools | Magnet Mask | Select/Deselect not working (/showthread.php?tid=2211)
[Fixed] Tools | Magnet Mask | Select/Deselect not working - Fonte Boa - 11-06-2016
Tools | Magnet Mask | Select/Deselect commands are not working.
Tested using Wings3D 2.1.2 (windows 7, 64-bits), but the problem was present in the anterior release too. I dont know since which version these commands are broken, but they were working fine in Wings3D 1.5.3 (i didnt install 1.5.4).
RE: Tools | Magnet Mask | Select/Deselect not working - dgud - 11-09-2016
They seem to work for me, but I admit I didn't know that it exited.
Though, it seems to be picky about selection mode restrictions,
but it was that in 1.5.3 too, which I used as reference when I tested this.
So can you be more specific about what works and what doesn't.
RE: Tools | Magnet Mask | Select/Deselect not working - Fonte Boa - 11-09-2016
1. Create a Sphere, smooth it twice (for example).
2. Make any selection (half sphere, for example).
3. Then call in top menu Tools | Magnet Mask | Lock (the selection wont react to Tweak Magnet tools). The locked vertices will appear in green.
4. Deselect all (space bar).
5. Finally, call Tools | Magnet Mask | Select. Nothing happens. Those locked vertices should be selected with this command (as happens in Wings 1.5.3).
I hope it is clear now.
RE: Tools | Magnet Mask | Select/Deselect not working - dgud - 11-10-2016
That works as expected for me both in 1.5.3 and 2.1.2, selected half of the faces.
Reset and Select a couple of edge rings, mask them.
Select all edges, Tools | Magnet Mask | Deselect
And the edges from the mask is deselected.
Anyone else having a problem?
RE: Tools | Magnet Mask | Select/Deselect not working - dgud - 11-10-2016
How does you window layout look like, I wonder if the commands are sent to the wrong window
or something?
If you do this with only a large geom window, does it work then?
I have had these kind of bugs before, but thought I fixed them.
Do you have keyboard shortcuts on the commands, if so can you remove those
and see if works.
Trying to figure out why it doesn't work for you and it works for me.
RE: Tools | Magnet Mask | Select/Deselect not working - Fonte Boa - 11-10-2016
Dgud, i just work using a single and large geometry window. To test those command (Tools | Magnet Mask| Select), i didnt call it by keyboard shortcuts: anyway i'll remove them to test again.
I'll record a video today night to show the problem to you, ok?
<< Reset and Select a couple of edge rings, mask them.
Select all edges, Tools | Magnet Mask | Deselect
And the edges from the mask is deselected. >>
Could you please try the following?
-Reset and Select a couple of edge rings, mask them.
-Deselect all edges, Tools | Magnet Mask | Select
-And the masked edges from the mask is selected.
RE: Tools | Magnet Mask | Select/Deselect not working - dgud - 11-10-2016
(11-10-2016, 10:23 AM)Fonte Boa Wrote: I'll record a video today night to show the problem to you, ok?
I don't know if that helps, I understand that it doesn't work for you I don't understand why.
Is anything printed in the log/console?
(11-10-2016, 10:23 AM)Fonte Boa Wrote: Could you please try the following?
-Reset and Select a couple of edge rings, mask them.
-Deselect all edges, Tools | Magnet Mask | Select
-And the masked edges from the mask is selected.
That works as expected, so it must be some difference between my config and yours.
RE: Tools | Magnet Mask | Select/Deselect not working - micheus - 11-10-2016
(11-09-2016, 10:23 PM)Fonte Boa Wrote: 5. Finally, call Tools | Magnet Mask | Select. Nothing happens. Those locked vertices should be selected with this command (as happens in Wings 1.5.3).
(11-10-2016, 10:23 AM)Fonte Boa Wrote: Could you please try the following?Both approach are also working here in v2.1, v2.1.2.
-Reset and Select a couple of edge rings, mask them.
-Deselect all edges, Tools | Magnet Mask | Select
-And the masked edges from the mask is selected.
RE: Tools | Magnet Mask | Select/Deselect not working - Fonte Boa - 11-10-2016
Very strange all this. I'll install Wings in another machine and post a feedback here.
RE: Tools | Magnet Mask | Select/Deselect not working - tkbd - 11-10-2016
Fonte Boa,What was the selection modes used in your workflow?
I tried reproduce that close condition by edge loop selection.
There are cases where it is not displayed depending on the selection mode.
-Make Sphere and smooth x 2
-(Edge Selection Mode)Select a couple of edge Loop, mask them.
-Deselect all edges
-Switch Face Selection Mode
-Deselect (Press a space key)
-(Then,switch to Multi Selection mode... ex. Vertex/Edge/Face)
-Tools | Magnet Mask | Select
-But selection area isn't appear.
But your case are used edge ring aren't you?
it is mysterious....
